For those of you that don't know or are not sure if or when you have seen an error, you will see an error during the normal boot up sequence. Instead of your booting the M$ dashboard or Hacked Dashboard (Evox, UnleashX, Avalaunch, etc.), there will be an message on the screen that says, "Your Xbox Requires Service" and you will see a number on the upper left hand corner of the screen <- this is your error code number. The error codes are listed below
Beware, you wont see the bootldr error's because (thanks to: Lordvader129) : "when you see this" is not entirely accurate, you never see the bootloader errors, as they are one that cause the reboot/FRAGs
2 - bootldr - Eeprom check failed
When you see this error most of the times you have flashed something wrong. Or you dropped solder on your eeprom chips.
4 - bootldr - Ram check failed
Your Xbox ram chips are wasted.
Maybe you dropped a little solder on it (try to remove it CAREFULLY!). Note, if they are fried, removing solder won't fix them). Maybe you were static when you touched the ram chips. They are kind off sensitive. If they are, they are fried, sell your xbox for spare parts.
5 - kernel - HDD not locked (The retail xbox bioses require the hd to be locked)
When you upgrade your hard disk drive for one that is larger, you most of the times use a new hard drive that you bought in the shop. Now, when you put this hdd in your xbox and you try to boot up with your chip off. It gives you error 5. Why you ask? Well i will try to explain it simple.
The original (also called "Retail") hard drive is locked by MS. Why did they lock the harddrive?
Well if it wasn't it wouldve been more than easy (in the start of xbox hacking)
for hackers to change content on it. Thats why MS locks it. It is just a security measure.
This locking proces uses information thats on the motherboard. The "Lock" on a xbox hard drive contains information that is based on the harddrive itself and the motherboard it came with.
One thing that makes this clear: You can not change a retail harddrive with another one from an other not modded xbox. With every xbox there is only ONE i repeat ONE compatible harddisk drive. That is, if they are locked.
If you don't mod your xbox (tsop or modchips) you can not change harddrives. Not even from another xbox. However when your xbox IS modified you can change your harddisk for almost every other harddisk (thats UNLOCKED). This means that even when your xbox is modified, you can not just put another (retail) XBOX harddisk in your xbox. However some smart people made programs that can lock or unlock your xbox harddisk on the fly.
So when does the error occur? The only time this error should occur is when you boot up your xbox in original mode AND you have a harddisk in your xbox that is not yet locked. So now you ask what do i have to do to make your xbox work again?
Well the answer is pretty easy. Boot up your xbox with the chip on. Preferably with a slayer evo-x cd. Now you choose "Eeprom management." Than you choose: "Lock hdd." It takes one second. After its ready it should say something like "Done"
When it is "Done" just turn off your xbox. Disable your chip and try to boot in original mode. Now there should be no more error 5.
6 - kernel - Cannot unlock HDD
If you understand the above, you should be able to understand what this means. It means you are trying to boot up the xbox with an harddisk that is locked in combination with ANOTHER motherboard than you are using it with right now.
What can i do about it, you ask? Well place the harddisk back in the xbox where it came from. After that, UNLOCK the harddisk with the same procedure i explained above (see error 5). Now when the harddisk is UNLOCKED, put it in the xbox which gave you the error. Now when you boot up with the chip ON it should not give you an error anymore.
However when you put the xbox on with the chip OFF your xbox will give you an error. (error 5) So to make sure you can boot original and boot with the chip ON. Next do the same as above: "Boot up your xbox with the chip on. Preferrably with a slayer evo-x cd. Now you choose "Eeprom management." Than you choose: "Lock hdd." It takes one second. After its ready it should say something like "Done"
When it is ready just turn off your xbox. Disable your chip and try to boot original. Now there should be no more error.
7 - kernel - HDD timeout
Most of the times, the IDE cable is not properly connected when you see this error. Please reattach the ide cable. Not only to the harddisk drive but also to the dvd drive. ALso try to reconnect the ide cable to the motherboard.
Press pretty hard so it goes all the way in. Make sure it is seated straight and proper in the drives and the motherboard. If you still have an error 7. Try another ide cable. If that won't work try another harddisk. If there is still no go, try to set the jumpers on the rearside of the harddisk drive. Set it to master or cable select. If still no succes, good luck and sell your xbox to me rolleyes.gif
8 - kernel - No HDD found
Please make sure your xbox hdd is attached properly. Most of the times the Ide cable came loose, or isn't seated properly in the IDE port of your harddisk. ALso make sure the power supply cables are intact and working.
Make sure the ide cable is also connected properly to the rest of the hardware (dvd and motherboard).
9 - kernel - HDD parameters (PIO/DMA/or size {debug}, certain size minimum is required for debug)
Not very common error, please try another harddisk.
10 - kernel - DVD timeout
Actually its almost the same as error 6/7/8. But also make sure the yellow cables are properly connected to the motherboard and the dvd drive.
1. Make sure ide cables are connected good.
2. Make sure the yellow cables are good and properly connected.
3. Still no succes? Try another dvd drive of which you are sure it is working.
11 - kernel - No DVD Found
Same as #10 So read up please!
12 - kernel - DVD parameters (PIO/DMA)
Same as #10, only not very common.
13 - kernel - Dashboard launch fail (due to missing/bad key, or anything else that would prevent it from running) and the dashboard didn't specify why it failed.
The error it gives is because of the incompatibility between the (older) dashboard (4920) that older slayer cd installs and the new dashboard/kernel versions found in some new xbox's and found in xbox's that have been connected to xbox live (when you go on xbox-live, it'll upgrade your dashboard file to i believe it is now 5659.03. This dasboard is incompatible with the dash that (old) slayer cd installs (for example 2.5 or lower) for you.
(In detail, in the eeprom chip there is a kernel which is incompatible with the dashboard (4920) that slayer installs.)
So what do you do to fix it? You can use the dashupdate found on most new xbox games! Be sure to 1st unplug your ethernet cable before you do so!!!
Besides that, just use a good installation disc and all is fine. Use a 2.6 slayer or something similar
Same thing as above (error 13). This time it is also a little mistake from you on changing names or having played around with files on the xbox harddisk. Error 14 is most often because you changed boot orders or names of startup files on the harddisk. It can also happen when you are rebuilding your xbox harddisk with a slayer cd and the power was cut.
16 - dashboard - Clock cannot be set.
Basically it comes down to this. Error 16 has to do with not finding the menu setting with which you can set the clock of the hdd. This happens to a lot of people that erase their hdd (original/upgraded) or MS dashboard files and after that they don't immediatly install the hdd but leave the xbox without power longer than 5 hours.
It's all about the hdd can't find the menu with which it can set the clock. This is mostly because the xbox hdd is empty (you removed dashboard or fux0red it via ftp). The problem arises when xbox searches for menu to set clock with, can't find it and voila: error 16. Well read on please!
So you have an error 16 huh? Don't worry "nothing" is broken!
You have an xbox hdd that is locked. And normally you can boot in original and modded mode. Retail or upgraded doesn't matter. You start playing around with xboxdash.xbe etc. using ftp programs. While doing this you "accidently" remove your MS dashboard and also your alternate dashboard (Evox, etc.) so there is no dash anymore on the xbox hdd.
You end the ftp session and after that you shut off your xbox. Normally when you would start up again it gives you an error 13/14 ( no dashboard found). No worries with a slayer Evox cd (and a hardmod), all is ok. BUT this is only WITHIN 3 hours or so.
This is because the internal clock of the xbox will only be kept alive by the capacitors for only 3 or 4 hours. So when you leave your xbox unplugged from electricity for over 5 hours after you have played with the .xbe's AND you have removed your (ms and evo-x) dash from your xbox than you are fux0red. Why do you ask?
Why can't I boot from disc?
Its as follows Xbox starts booting==> (almost 1st thing a xbox does is) searches for internal clock==> doesnt find internal clock because there hasn't been any electricity on the xbox for 5 hours so battery that kept clock alive is empty and clock is gone==> searches for the proper dashboard menu to set clock with ==> doesnt find msdashboard or evo-x dashboard menu becuz you have removed it from the hdd for whatever reasons you had==> xbox gives error 16: cannot set clock.
So what do you do about it? Two options!
1. There are some bios'es around that allow the chip to boot past the clocksetting. (do a search!). So how do you get that bios on your chip because you cant boot to a flash program or something? Well you need to have an external flasher.
It seems the m8 bios will take care for you of booting past the clocksetting. Or use the latest Xecutor bios
2. This is the more easy and newbie friendly strategy
-Get a friend with a modded xbox.
-Unlock his hdd with eeprom management from a slayer evo-x cd.
-Than, place his hdd in your xbox.
-Boot with your chip on.
-Now the xbox DOES find a dashboard when you boot in original mode and you can set the time in the msdashboard clock settings.
-Shut off xbox and remove your friends hdd
-PLace his hdd back in his xbox and lock it again
-Install your hdd
-(clock has been set) So boot up with slayer cd.
-Install normally whatever you wanna install
-lock hdd
If you get an error 13 after this, please read up on the error 13 explanation!
20 - kernel - The dashboard was attempted to load and failed
It was a cold boot, and the dashboard didn't specify why it failed, but it
(for some reason) needed to be noted that the dvd passed the challenge/response authentication
21 - anywhere -
This error says that the machine was booted to display a error, basically someone told the machine to reboot (or launch a xbe) with this flag, and the error code just means its been rebooted by the flag
This occurs frequently when the xbox is unable to boot due to dashboard changes being made (ie Gcue true blue hasnt been resigned, parts of the stock dash are missing - incomplete FTP backups copied to a new HDD for example). _________________
DJB Administrator
Joined: May 23, 2003 Posts: 4031 Location: NSW, Australia
Posted: Sun Jul 31, 2005 4:11 am Post subject:
Nice work here
I've made this thread a sticky so others can use as reference.
DJB Administrator
Joined: May 23, 2003 Posts: 4031 Location: NSW, Australia
Posted: Sun Jul 31, 2005 2:09 pm Post subject:
BTW, just to clarify, did you get this from another tutorial at all, and if so where?
RIP1982 Xbox-HQ Elite Member
Joined: May 14, 2004 Posts: 323 Location: Nasti Nati
You're 100% correct, and it's a direct copy / paste.
If this is ever done, please reference the original place you got the info (just a note in future for everyone).
crazyshorty89 Xbox-HQ Experienced
Joined: Jul 27, 2005 Posts: 118 Location: Australia
Posted: Mon Aug 01, 2005 8:14 am Post subject: Ohh shit
Sorry i didnt know i have copy/pasted a few things onto this site sorry didnt know (noob)
if you have noticed i havent claimed it as my own. _________________
DJB Administrator
Joined: May 23, 2003 Posts: 4031 Location: NSW, Australia
Posted: Mon Aug 01, 2005 9:49 am Post subject:
Yea I know you didn't claim it to be your own or anything, just when you grab something like that from somewhere try and credit the original site / author.
crazyshorty89 Xbox-HQ Experienced
Joined: Jul 27, 2005 Posts: 118 Location: Australia
Posted: Mon Aug 01, 2005 11:01 am Post subject: Yeh man
For sure will do for now on. _________________
forahobby Administrator
Joined: May 22, 2003 Posts: 23945 Location: NSW, Australia
Posted: Sat Aug 27, 2005 5:23 am Post subject:
nice find crazyshorty..
We actually have our own error codes tutorial too here:
When i boot my xbox I dont see an error code anywhere. All the screen says is your xbox requires service. Please call xbox customer support. and in a few other languages, so do you know what is wrong if i dont get a number in the upper left??
RastaCalavera Xbox-HQ Experienced Xbox Version: V1.6 x2 Modded: UnleashedX/Evolution X
Joined: Mar 08, 2007 Posts: 112 Location: Minneapolis
Posted: Sun Mar 18, 2007 4:55 am Post subject:
any idea what error 112 is? _________________ RastaCalavera
DJB Administrator
Joined: May 23, 2003 Posts: 4031 Location: NSW, Australia
Posted: Sun Mar 18, 2007 7:25 am Post subject:
RastaCalavera wrote:
any idea what error 112 is?
Are you sure that's not a Xbox 360 error dode, becuase Xbox 1 error codes only go up to 21 / 22.
Burner6999 Xbox-Hq Genius Xbox Version: V1.6 x2 Modded: UnleashedX/Evolution X
Joined: Aug 15, 2006 Posts: 1426 Location: Colorado
Posted: Sun Mar 18, 2007 9:27 am Post subject:
Yeah it either happens with Unleash X when you try to move something from the dvd drive or when you try to copy something to the hard drive that wont fit.
|
All times are GMT |Page 1 of 1
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
HQ Network: 8,183 | 
Guests: 2068 | 
Members: 0 
Forums 
