OK here's a few updates.


Here's a picture of the Xecuter2.3b LITE. Easy to recognise with the new color (X2.3 are red pcbs).

First of all it has become apparent that the X2.3 Lite & Lite+ USB adapter is not working on some consoles. We have found that certain versions have a larger socket header which makes the adapter a little loose. We've also found a small batch of adapters that have an error on the PCB which stops one of the gamepad ports from working. This is an intermittent issue and all suppliers have been shipped stocks of spare parts to send out to those who need them. We can only apologize for the inconvenience and promise to work with you to resolve the issue.

We have been active on our forums to help those with problems. Many have posted fixes and success stories, but of course there will always be some who just can't get it to work. We have made sure all customers of official retailers are in the position to return their non working mod for a new Xecuter 2.3B, which is a slightly modified version that no longer needs the 3.3v source. More info on that in a couple of hours - we're just finishing up the guides for you.

Finally we would like to offer our congratulations to OzX & Xodus in their new partnership. We are especially glad that Xodus have fixed themselves up after their recent debacle and we look forward to a healthy bout of competition in the new year.

On that note from all the staff at Xecuter we wish the entire scene a Happy Christmas and a Prosperous New Year. See you in 2004 !

I found this thread (by xecuter) for those who have problems with their original X2.3 lite/liteplus:

OK its become obvious that there seems to be an intermittent issue with some xbox's and the 2.3 lite and lite+

First of all the mod does work. The problems are a small minority of users - but granted we accept it is a larger amount than usual.

For 2.3 Lite:
1. If you get the cromwell screen but your game pad is not working on 1 or more of the ports then you either don't have a tight connection between the adapter and the motherboard (some suggest use some electrical tape) or you have a faulty usb adapter.
Solution: Official suppliers have been sent spare parts - so simply request the adapter.
2. If you do not get the cromwell screen and you get a FRAG but your mod lights up with 2 blue LED's then you either have a bad ground connection or your LPC points need resoldering or the mod is not stuck to the side of the case as low as possible to the motherboard with the wires nice and flat against the motherboard.
Solution: Position the mod as instructed. If you still get FRAG then make sure your ground points all connected correctly with the star washer. You can also add the pin header d0/ground adapter to add yet another ground. Messy yes but it might solve your problem. If this still doesnt work send the mod back to your supplier for a replacement. You can also try to cut the 2 black wires that go to the usb adapter and solder them to LPC#6 (5v).

3. If you do not get the cromwell screen and you get a FRAG plus your blue LED's do not lite up this indicates you have no power. Try to fit the USB adapter firnly and correctly with all cables plugged in correctly. If still no luck - send the mod back to your supplier for a replacement.

For 2.3 Lite+:
1. Read all points above.
2. Make sure the d0 is prepped first. Use a fibre glass pen or an exacto kinfe to clean up the area so a metal contact shows through. Fit the mod and screw in as tight as it will go without going in too hard. You should feel the pressure easily if you take your time. Make sure the switch is fitted correctly and then disable the mod. Turn the power on the xbox and you should get 2 blue led's and a green led. if the green led flickers on/off it is not a solid connection (this normally points towards a badly prepped or none prepped d0). If you do not get the green led simply wiggle the mod around gently until you do. While doing all this there is no need to have your hard drive or dvd rom connected. When you get all 3 leds turn off the xbox. Enable your mod. Turn the xbox on. Th green led will go off and you should get the cromwell screen or the tray will eject with no video on screen (v1.4 v1.5 boxes). if you gt a FRAG or the default ms dash simply repeat the "wiggling" procedure. I've not ever spent more than 60 seconds getting a mod to work like this.

If you have tried all of the above then it's obviousley possible your mod is faulty. There is no need to freak out this does happen in electrical manufacturing. However all users who buy from official sources are fully supported and you have a guarantee. Simply contact your distributor and get them to replace with a new mod.