kidcurrie Xbox-HQ User Xbox Version: v1.6 Modded: duo
Joined: Oct 04, 2004 Posts: 11 Location: kalgoorlie, WA
Posted: Sat Feb 12, 2005 5:04 am Post subject: Xbox not turn on
My xbox after adding a modchip, by myself, will not start. When I turn it on the eject Led flashes green for a second then turns off, then flashes green for a sceond and turns off then it flashes red/green alternatively, does anybody know what I have stuffed up in my Xbox
thanks
V1.1 Aladdin Advance - permanently turned on modchip
RIP1982 Xbox-HQ Elite Member
Joined: May 14, 2004 Posts: 323 Location: Nasti Nati
Posted: Sat Feb 12, 2005 5:07 am Post subject:
you should double and tripple check the d0 point and make sure it is making good contact. _________________ [RIP Radio]
24-7 streaming internet radio
*works on windows pcs with IE or FF*
TheModGod Xbox-Hq Legendary Xbox Version: v1.6 Modded: duo
Joined: Apr 18, 2004 Posts: 5303 Location: Greensburg PA
Posted: Sat Feb 12, 2005 5:07 am Post subject:
You have one of two problems.
Bad Bios
Bad install.
Eliminate the install possibility by checking your solderless adapter for proper alignment if you have solderless.
If you used soldering iron, check your pin header area. Make sure there are no gaps in the lpc holes. Make sure you have no solder splash. Make sure you have no solder bridges.
Disconnect the D0 wire and make sure your Xbox boots normally, if it does then you should be in good shape as far as NOT having a damaged mobo.
I would then try to wipe the chip clean of any flashes on it. If you have a programmer to flash the chip, try reflashing it. The bank may be corrupt or have the wrong size bios to it.
TheModGod
-------------------------
http://www.themodgod.com http://www.xbox-hq.com _________________ Good Deals: Death@Hand, funkydopenloven, StaticMind, Slamscaper, PorscheXboxter
Bad Deals: None Yet
Pending Deals: Vanguard
TheModGod Xbox-Hq Legendary Xbox Version: v1.6 Modded: duo
Joined: Apr 18, 2004 Posts: 5303 Location: Greensburg PA
Posted: Sat Feb 12, 2005 5:10 am Post subject:
Quote:
you should double and tripple check the d0 point and make sure it is making good contact.
I have never installed an Aladdin, so correct me if I am wrong. But, if the D0 is not connected securely, wouldn't it just boot normally?
Then, if he had a blank HD and the Xbox booted normally, he wouldn't get the on and off power cycle, he would just get a dashboard error most likely (21 or 13).
I think that the fact he's getting the frag tells him the D0 is making good contact.
TheModGod
----------------------
http://www.xbox-hq.com http://www.themodgod.com _________________ Good Deals: Death@Hand, funkydopenloven, StaticMind, Slamscaper, PorscheXboxter
Bad Deals: None Yet
Pending Deals: Vanguard
kidcurrie Xbox-HQ User Xbox Version: v1.6 Modded: duo
Joined: Oct 04, 2004 Posts: 11 Location: kalgoorlie, WA
Posted: Sun Feb 13, 2005 9:14 am Post subject:
Thanks for the replies, the mobo was sent in for repair and it worked fine for the repairer, (TSOP was stuffed but the modchip worked). when I got it back the BT needed resoldering, have checked the join and it looks good. Any other possibilities
Kid
|
All times are GMT |Page 1 of 1
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
HQ Network: 8,608 | 
Guests: 2093 | 
Members: 1 
Forums 
