I am going to the wire installation method, finding it easyer to do..
I have all the materials shows in the pictures on the site.
I have connected the 1.6 converter PCB with 1.6 wire harness on the left and the 1.6 wire converter on the right.
The wire converter is going to the Xbit PCB on the top.
The black and yellow wires are connected to the external PCB. and the usb cable connected exteral PCB.
Now having that said, the wire harness ( the one shown on the first page of materials) is left,
I solder the v1.6 wire harness to the plc port as shown in figure # 7
However, not wanting to have the modchip on all the time iam going to take the orange wire from the v1.6 wire harness and take the orange from the regular wire harness and connect them and routing them to the top as shown in figure 9 and 10
With me so far, now i get confused...
It says to "Now rebuild the LPC port" using the section below with is not there..
I have no clue what to do ??
i have looked at the pictures on the dms3 site but there only picutes no instructions.
and which wires do i use to rebuild the plc port?? i am think the wire harness (which i took out the orange wire) since i see no use for that...
If i do all that including the now rebuild the lpc port am i done with installing my mod chip?? ( i have already flashed it with EvolutionM8 plus)
Also , i have the Modchip dvd power harness? can you explain where than is connected , there are yellow wires on each side, with and red and black wires seperating...showin the site
impwiz V.I.P. Lifetime Xbox Version: all Modded: everything
Joined: Aug 30, 2005 Posts: 1070 Location: Detroit
Posted: Mon May 29, 2006 3:12 am Post subject: Re: X bit people look hear... explain my proble here clearly
Cream wrote:
1. I solder the v1.6 wire harness to the plc port as shown in figure # 7
However, not wanting to have the modchip on all the time iam going to take the orange wire from the v1.6 wire harness and take the orange from the regular wire harness and connect them and routing them to the top as shown in figure 9 and 10
With me so far, now i get confused...
2. It says to "Now rebuild the LPC port" using the section below with is not there..
I have no clue what to do ??
3. i have looked at the pictures on the dms3 site but there only picutes no instructions.
and which wires do i use to rebuild the plc port?? i am think the wire harness (which i took out the orange wire) since i see no use for that...
If i do all that including the now rebuild the lpc port am i done with installing my mod chip?? ( i have already flashed it with EvolutionM8 plus)
4. Also , i have the Modchip dvd power harness? can you explain where than is connected , there are yellow wires on each side, with and red and black wires seperating...showin the site
1. could you be more clear? Are you going to put a switch or something in?
2. look at the DMS site's pictures, and make sure they match yours. Never mind the words. I think the LPC rebuld is the small pcb that the multi-color harness plugs in (SEE PICTURE ATTACHED- That's the LPC rebuild).
3. the orange wire is there for a reason. So the chip works. it's part of the 1.6 rebuild. Figure #10- solder the orange wire to that regulator's leg.
4. Replace your current dvd power harness with the supplied. Then, plug it in your chip.
XBIT.gif
Description:
1.6 LPC rebuild
Filesize:
51.45 KB
Viewed:
292 Time(s)
_________________
Cream Xbox-HQ Newbie Xbox Version: all Modded: everything
Joined: May 26, 2006 Posts: 7
Posted: Mon May 29, 2006 3:34 am Post subject: yes
yes i have them...
the 1.6 wire harness and 1.6 converter harness are both connected to the 1.6 converter PCB. Also shown in the link in my previous post....
and explaind in the post too.
there are two wire harness!
however in the manual only one is shown to be in use.... which is the 1.6 and the other one has no instructions on what it should done with
one is 1.6 wire harness which goes into the 1.6 converter PCB and the other one is just a wire harness.
if you look again at the site...it shows your two wire harness
Now since the manual is not full , the lpc rebuild is what is left out...
and since the wire harness( not the 1.6 one is not being used expect the orange wire which is extended to the other orange wire as shown in the manual figure 9 and 10 ) i am thinking i have to take the wires off that and rebuild the lpc port? correct??
3. the orange wire is there for a reason. So the chip works. it's part of the 1.6 rebuild. Figure #10- solder the orange wire to that regulator's leg.
i have done that...
now there a wire harness with out an orange wire...
and with that wire harness i need to take the other wires and rebuild the lpc
this is were i need help..
|
All times are GMT |Page 1 of 1
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
HQ Network: 8,521 | 
Guests: 2482 | 
Members: 0 
Forums 
